中文字幕日韩在线观看,久久久人人玩人妻精品综合,国产欧美日本在线,久久精品免费视频6,欧美精品黄色网站,色综合久久久久无码专区,亚洲区欧美中文字幕久久,国产手机在线视频,国产中文字幕视频在线观看,日本一区二区免费在线观看

Hotline:400-880-1556

English




Project Introduction

Tensile strength test can also be called tensile test for metal mechanical properties. Tensile test can measure a series of strength indexes and plastic indexes of materials. Strength usually refers to the ability of a material to resist elastic deformation, plastic deformation, and fracture under external force. Plasticity refers to the ability of a metal material to deform plastically under load without damage. Commonly used plasticity indicators are elongation and shrinkage.

Guideline

Reference standard for tensile strength test

GB-T228-2002 Metallic materials Tensile test method at room temperature

ASTM E8-04 Metal Tensile Test Method Metal Tensile Strength Test

EN 10002-1:2001 Tensile test of metallic materials, normal temperature test method

JIS Z 2241:1998 Metallic material tensile test method

ISO 6892:1998 Metallic materials, tensile test at ambient temperature

experiment procedure

image.png

Elastic zone (from 0 to yield strength YS)

· Less elongation: corresponding percentage.

· Elastic elongation: If the stress stops, the sample will return to its original length.

· Yield strength: when the permanent elongation value reaches 0.2%.

· Yield strength = force at yield (N) / original area of the tensile specimen (mm2) or the same MPA value.

· Longitudinal modulus: ratio of applied force to elongation length (depending on metal).

· Transverse modulus: the ratio of elongation to interface shrinkage (applies to all metals ~ 0.3).

Plastic zone (from tensile strength UTS to yield strength YS)

· Large elongation: a few percent for general metals, up to 50 to 60 percent.

· Inelastic elongation: if the stress stops, the specimen remains permanently strained.

· Breaking force: record of tensile strength (UTS).

· Tensile strength = maximum force (N) before breaking the tensile test / original area of the tensile specimen (mm2) or the same MPA value.

· Due to the cold work effect, the strain will continue to increase with the test.

After breaking

· The overall length needs to be measured to calculate the elongation.

· E% = (Lu – L0) / L0 x 100 (Lu is the final length, L0 is the initial length).

Young's modulus-important parameter

· Modulus of elasticity E: unit N/mm2.

· Yield strength YS 0.2: Unit N/mm2 or MPa.

· Transverse modulus: Poisson coefficient, always around 0.3.

· Breaking force: UTS, unit N/mm2 or MPa, except in special cases.

· Elongation at break E%: ductility, E<5% is brittle (brittleness).

· Executive standards: NF EN 10002 and ASTM E8, the difference between the two is the measurement difference (L0) of different elongation values.


Online consultation

Online consultation

Recommend
  • BSCI certification

    BSCI certification

    BSCI certification is an abbreviation of BusinessSocialComplianceInitiative, and Chinese is called business social standard certification. BSCI is an organization that advocates the business community to abide by social responsibility. At the same time, it is a non-profit organization.

  • Enterprise CMA certification

    Enterprise CMA certification

    CMA, the name is \"China Metrology Accreditation\", the abbreviation of \"China Metrology Accreditation\" in English. According to the provisions of Article 22 of the Metrology Law of the People’s Republic of China: “The product quality inspection agency that provides notarized data to the society must be evaluated by the metrological administrative department of the people’s government at or above the provincial level for the capability and reliability of metrological verification and testing. Qualified.\"

  • CNAS certification

    CNAS certification

    Laboratory accreditation is a third-party certification that CNAS has the ability to perform specific testing and calibration work for testing and calibration laboratories.

Tensile strength test

Tensile strength test can also be called tensile test for metal mechanical properties. Tensile test can measure a series of strength indexes and plastic indexes of materials. Strength usually refers to the ability of a material to resist elastic deformation, plastic deformation, and fracture under external force.

Get a quote
毛片av网站| 国内自产少妇自拍区免费| 亚洲日韩av一区二区三区中文| 亚洲色精品三区二区一区| 无码精品尤物一区二区三区| 野花社区www视频日本| 日韩日韩日韩日韩日韩日韩 | 国产特黄级aaaaa片免| 日本亚洲色大成网站WWW久久 | 国产一区二区三区免费视频 | 2021久久伊人精品中文字幕有| 中文字幕乱码人妻综合二区三区| 国产a级毛片| 亚洲中文字幕无码永久在线不卡| 国产精品精品国产一区二区| 久久伊99综合婷婷久久伊| 特黄a级毛片| 非洲黑人性xxxx精品| 一出一进一爽一粗一大视频| 日本VA欧美VA精品发布| 国产成人无码A区视频在线观看| 日韩无码影视| 99精品国产成人一区二区在线| 日韩精品人妻系列无码av东京 | 色综久久| 天天躁日日躁狠狠躁人妻| 国产精品久久777777换脸| 久久久久人妻一区精品色欧美| 亚洲av首页在线| 九月婷婷人人澡人人添人人爽| 老汉色av影院| 亚洲成a人片在线观看无码3d| 人人鲁人人莫人人爱精品| 青草草在线视频永久免费| 国产精品99无码一区二区| 国产三级国产经典国产AV| 蜜桃久久国产一区二区| 国产免费一区二区三区VR| 亚洲高清毛片一区二区| 四虎影视永久无码精品| 国产人成视频在线观看|